Share information:
Diesel turbocharging system car Toyota Corona 9 (T190)
Turbocharging system — general description
In order to force the engine to increase the amount of air entering the engine, and hence the fuel, one or another type of boost is used. On 2C-T engines, a turbocharger is installed, which uses the energy of spent...
In order to force the engine to increase the amount of air entering the engine, and hence the fuel, one or another type of boost is used. On 2C-T engines, a turbocharger is installed, which uses the energy of spent...
Turbocharger checks on a car
1. Check the intake and exhaust system. A) Check for leaks and blockages between the air filter and the air duct, and between the air duct and the cylinder head. Replace defective elements if necessary. Eliminate any...
1. Check the intake and exhaust system. A) Check for leaks and blockages between the air filter and the air duct, and between the air duct and the cylinder head. Replace defective elements if necessary. Eliminate any...
Removing the turbocharger
Removal and installation of a turbocharger: 1 - heat shield No. 2, 2 - heat shield No. 1, 3 - outlet pipe, 4 - turbocharger assembly, 5 - actuator, 6 • air hose, 7 - coolant supply pipes, 8 - cooling system hoses, 9 -...
Removal and installation of a turbocharger: 1 - heat shield No. 2, 2 - heat shield No. 1, 3 - outlet pipe, 4 - turbocharger assembly, 5 - actuator, 6 • air hose, 7 - coolant supply pipes, 8 - cooling system hoses, 9 -...
Turbocharger check
1. Check wheel rotation. Make sure the wheels turn smoothly. If the wheels do not rotate or rotate with resistance, replace the turbocharger. 2. Check the axial clearance of the compressor shaft. Install the dial...
1. Check wheel rotation. Make sure the wheels turn smoothly. If the wheels do not rotate or rotate with resistance, replace the turbocharger. 2. Check the axial clearance of the compressor shaft. Install the dial...
Checking the turbocharger actuator
1. If necessary, remove the actuator. A) Disconnect the air hose. b) Remove the two bolts securing the actuator to the turbocharger housing. V) Remove the retaining ring that secures the stem to the valve and remove the...
1. If necessary, remove the actuator. A) Disconnect the air hose. b) Remove the two bolts securing the actuator to the turbocharger housing. V) Remove the retaining ring that secures the stem to the valve and remove the...
Turbocharger Installation
Attention: after installing the turbocharger, fill 20-30 cm 3 fresh oil into the bearing housing and turn the compressor shaft by hand. 1, Install a new gasket, turbocharger bearing holder cover and tighten the two...
Attention: after installing the turbocharger, fill 20-30 cm 3 fresh oil into the bearing housing and turn the compressor shaft by hand. 1, Install a new gasket, turbocharger bearing holder cover and tighten the two...
Absolute pressure sensor — check
1. Power check. A) Disconnect the sensor connector. b) Turn on the ignition. V) Measure voltage between terminals "VC" And "E2" connector. Supply voltage 4.5-6.5 V. G) Switch off the ignition. d) Connect the sensor...
1. Power check. A) Disconnect the sensor connector. b) Turn on the ignition. V) Measure voltage between terminals "VC" And "E2" connector. Supply voltage 4.5-6.5 V. G) Switch off the ignition. d) Connect the sensor...
Boost pressure control electropneumatic valve
Removal and installation of electropneumatic valve: 1 - connector for the electro-pneumatic valve of the boost pressure corrector, 2 - connector for the electro-pneumatic valve for increasing the speed when the air...
Removal and installation of electropneumatic valve: 1 - connector for the electro-pneumatic valve of the boost pressure corrector, 2 - connector for the electro-pneumatic valve for increasing the speed when the air...
This section is available on: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Similar sections for other Toyota models
➥ Power unit: Turbocharging system Toyota Cruiser 70 (1985-1996, diesel)
Link in different formats to this article
TEXTHTMLBB Code
- General information
- User manual
- Maintenance
- Power unit
- Engines 3S-FE/GE and 4S-FE
- Engines 4A-FE and 7A-FE
- Engines 5E-FE
- Diesel engines 2C and 2C-T
- Engine overhaul
- Cooling system
- Lubrication system
- Fuel injection (petrol)
- Control system (petrol)
- Fuel system (diesel)
- Turbo diesel
- Ignition system
- Engine electrical equipment
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Drive shafts and cardan
- Chassis, running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Body and interior
- Body and interior elements
- Doors, windows and locks
- Heating and air conditioning
- Electrical equipment
- Equipment and devices
- Lighting and signaling
- Electrical circuits