2. Rotate the adjusting tube to disassemble the lower control arm #2.
 |  |
3. Turn away locknuts from levers.
2. Rotate the adjusting tube to disassemble the lower control arm #2.
3. Turn away locknuts from levers.
Disassembly of the lower suspension arm No. 2
1. Loosen the two lock nuts.
2. Rotate the adjusting tube to disassemble the lower control arm #2.
3. Turn away locknuts from levers.
2. Rotate the adjusting tube to disassemble the lower control arm #2.
3. Turn away locknuts from levers.
This article is available at: russian, bulgarian, belarusian, ukrainian, serbian, croatian, romanian, polish, slovak, hungarian
Share information:
Lower and trailing arms (2WD) — withdrawal
The device of the lower and longitudinal suspension arms
Rear suspension strut — installation
Rear suspension strut — removal
Rear suspension strut device
Replacing the front axle hub bolt
Installing the steering knuckle with the front axle hub
Assembling the front axle hub
Disassembly of the front axle hub
Front axle hub device
The device of the lower and longitudinal suspension arms
Rear suspension strut — installation
Rear suspension strut — removal
Rear suspension strut device
Replacing the front axle hub bolt
Installing the steering knuckle with the front axle hub
Assembling the front axle hub
Disassembly of the front axle hub
Front axle hub device
Lower Suspension Arm Assembly #2
Lower and trailing arms (2WD) — installation
Lower and trailing arms (4WD) — withdrawal
Lower and trailing arms (4WD) — installation
Rear wheel hub device (2WD)
The device of the stabilizer bar of the rear suspension
Rear suspension anti-roll bar — removal and installation
Checking the rear stabilizer bar
Rear wheel hub (2WD) — removal and installation
Disassembly of the rear wheel hub
Lower and trailing arms (2WD) — installation
Lower and trailing arms (4WD) — withdrawal
Lower and trailing arms (4WD) — installation
Rear wheel hub device (2WD)
The device of the stabilizer bar of the rear suspension
Rear suspension anti-roll bar — removal and installation
Checking the rear stabilizer bar
Rear wheel hub (2WD) — removal and installation
Disassembly of the rear wheel hub
Similar articles on other Toyota models
➥ Suspension strut and spring — disassembly and assembly Toyota Camry XV20 (1996-2001)
➥ Replacing the lower left arm of the front suspension No. 1 Toyota Corolla Verso 3 (2004-2009)
➥ Disassembly and assembly of the lower suspension arm No. 2 Toyota Corona T190 (1992-1997)
➥ Removal and installation of the lower operating lever of a forward suspension bracket Toyota Cruiser 100 (1998-2007)
➥ Disassembly of elements Toyota Highlander 1 (2000-2007, petrol)
➥ Steering Suspension Check Toyota 4Runner N120 (1989-1995)
➥ Lower arm front suspension — removal and installation Toyota RAV 4 XA10 (1994-2000)
➥ Lower arm front suspension Toyota Duet (1998-2004)
Link in different formats to this article
TEXTHTMLBB Code
Comments and feedback from visitors
No comments yet
- General information
- User manual
- Maintenance
- Power unit
- Engines 4A-FE, 5A-FE, 7A-FE
- Engines 3S-FE, 4S-FE
- Diesel engines 2C
- Engine repair
- Cooling system
- Lubrication system
- Fuel system
- Control system (diesel)
- Fuel injection system
- Engine electrical equipment
- Transmission
- Clutch
- Mechanical gearbox
- Automatic gearbox
- Drive shafts
- Chassis, running gear
- Car suspension
- Steering
- Brake system
- Body and interior
- Exterior (external elements)
- Interior (internal elements)
- Air conditioning and heater
- Electrical equipment
- Equipment and devices
- Headlights and lighting
- Breakers and switches
- Electrical circuits
- General information
- Introduction to the manual
- Power unit
- Gasoline engines
- Diesel engines
- Lubrication system
- Cooling system
- Fuel system (carburetor)
- Fuel system (injector)
- Ignition system
- Transmission
- Clutch
- Car gearbox
- Drive shafts
- Chassis, running gear
- Front suspension
- Rear suspension
- Steering
- Brake system
- Electrical equipment
- Power devices
- Electrical circuits